Mitsubishi Center Bearing Bracket OEM ME000076

1. Introduction

In the driveline of Mitsubishi Fuso Canter trucks, the driveshaft center bearing bracket plays a critical role in supporting the multi-piece propshaft where it connects front and rear sections. Identified by OEM number ME000076, this component uses a rubber-bonded bearing to absorb torsional vibration and minor shaft misalignment during operation. For OEM buyers, wholesalers, and workshops across Europe and North America, sourcing a Mitsubishi ME000076 driveshaft center bearing bracket with accurate dimensions and a stable rubber compound is essential to protecting aftermarket quality and customer satisfaction.

2. Technical Overview

2.1 Structure

The Mitsubishi ME000076 driveshaft center bearing bracket consists of three main elements: a stamped steel bracket body, a vulcanized rubber isolator, and an embedded sealed ball bearing. The steel bracket bolts to the frame crossmember at two points, while the rubber isolator forms a flexible layer between the bracket and the bearing outer race — carrying radial load from the rotating propshaft while isolating vibration from reaching the frame and cab.

2.2 Material and Manufacturing

The rubber component uses an NR/NBR blended compound, combining the elasticity and rebound of natural rubber with the oil and aging resistance of nitrile rubber — suited to the truck's underbody exposure to oil, dust, and temperature swings. The rubber is bonded to the steel insert through a vulcanization process for a one-piece structure that resists debonding or delamination, with hardness controlled at 60±5 Shore A to balance vibration damping with structural support. The bearing itself is a sealed deep-groove ball bearing, pre-packed with grease at the factory to reduce early wear.

2.3 Performance Advantages

• Reduces driveshaft-induced noise and vibration for better overall NVH

• Rubber compound resists heat, oil contamination, and ozone aging for extended service life

• Dimensional tolerances held to OEM drawing specifications for direct bolt-on fit

• Supports the multi-piece propshaft with allowance for slight axial and angular compensation

2.4 Cross-OEM Relationship

Some model years of the Mitsubishi Fuso Canter share a related part family for the center bearing assembly — for example, MB563228 is a related Canter Fuso propshaft center bearing assembly. Buyers are advised to confirm fitment against the chassis VIN and production year to avoid mismatches caused by mid-cycle running changes.

3. Vehicle Application List

*This fitment list is compiled from publicly available platform data for the related driveshaft assembly. Please confirm exact chassis-level fitment against Mitsubishi's official TecDoc records and the vehicle's chassis plate.

4. Cross-Reference

*Cross-reference numbers are provided for guidance only. Please verify against TecDoc or engineering drawings before ordering to avoid mismatched parts.

5. Typical Failure Symptoms

1. Clunking or knocking noise from under the vehicle during acceleration or deceleration

2. Noticeable vibration through the floor pan or seat at highway speed

3. Visible cracking, splitting, or debonding of the rubber isolator

4. Excessive bearing play when the propshaft mid-section is pushed up and down by hand

5. Growling or humming noise that increases with vehicle speed (worn bearing)

6. Uneven tire wear or persistent drivetrain vibration from shaft misalignment

6. Key Specifications

*Exact dimensions should be confirmed against engineering drawings and physical measurement. CAD drawings and test reports are available on request.

7. Installation Notes

1. Support the propshaft securely with a stand before removing the bracket bolts to prevent it from dropping

2. Mark the alignment/index position at the shaft joint before disassembly to preserve driveline balance on reassembly

3. Torque the mounting bolts to the manufacturer's specification in a criss-cross sequence

4. Avoid over-torquing, which can pre-load the rubber isolator and shorten its service life

5. Inspect the universal joints and slip yoke for wear at the same time and replace if needed

6. Road test after installation to confirm vibration and noise have been fully resolved

8. Frequently Asked Questions

Q1: What does the ME000076 center bearing bracket do?

It supports the middle section of the multi-piece propshaft on Mitsubishi Fuso Canter trucks, using a rubber-bonded bearing to absorb torsional vibration and minor misalignment for smooth driveline operation.

Q2: How can I tell if a center bearing bracket has failed?

Common signs include knocking noise during acceleration/deceleration, increased vibration at highway speed, visible cracking of the rubber, and excessive play when the propshaft is moved by hand.

Q3: Which Mitsubishi Fuso Canter models use OEM ME000076?

It covers multiple model years across the Canter FE, FG, FB, and TF series — see the Vehicle Application List above, and confirm against the chassis VIN.

Q4: Can I replace just the bearing instead of the whole bracket?

Since the rubber isolator and bearing housing are vulcanized into a single unit, replacing the complete bracket assembly is generally recommended to preserve damping performance and fitment accuracy.

Q5: How long does a driveshaft center bearing bracket typically last?

Under normal operating conditions and with routine inspection, it typically lasts well beyond typical service intervals, though actual life depends on road conditions, load, and maintenance.

Q6: Why does the rubber compound matter?

The compound determines vibration isolation, oil and weather resistance, and service life. An NR/NBR blend balances elasticity with durability, avoiding premature cracking or excessive softening.

Q7: Is ME000076 cross-compatible with aftermarket brands like Febi or MEYLE?

Cross-compatibility is possible, but tolerances and rubber formulations vary by brand, so buyers should verify specific cross-reference numbers before ordering — see the Cross-Reference section.

Q8: Do you support private label (OEM/ODM) bulk orders?

Yes. We offer custom packaging, private labeling, and supporting certification documents to meet market entry requirements in Europe and North America.

Q9: What is the MOQ and lead time for ME000076?

MOQ and lead time depend on order size and specification. Contact our sales team for a detailed quotation.

Q10: How do I request a sample or quote?

Reach out to Hebei Tongsource International Trade Co., Ltd. by email or our online inquiry form, and we will respond with sample options and a formal quotation within 24 hours.

9. Conclusion & Call to Action

As a key component in keeping the Mitsubishi Fuso Canter's driveline running smoothly, the ME000076 center bearing bracket's rubber formulation, bearing precision, and dimensional tolerance directly affect vehicle NVH and aftermarket reputation. Hebei Tongsource International Trade Co., Ltd. is the wholly-owned export subsidiary of Beijing Stock Exchange-listed Hebei Huami New Material Technology Co., Ltd. (stock code: 920247), drawing on the parent company's manufacturing depth in rubber damping components, sealing products, and engineering plastics to supply OEM-quality driveshaft brackets and one-stop export service to OEM manufacturers, wholesalers, and repair chains worldwide. Contact us today for samples, test reports, and a formal quotation to grow your business in the European and North American markets.